CG FC200 ECU Programmer Full Version with MPC5XX Adapter for BOSCH MPC5xx Read/Write Data on Bench

FC200 Highlights

1. Bundle Deal with CG FC200 Full Version and MPC5XX Adapter

Includes CG FC200 Full Version with all licenses activated and the CG FC200-MPC5XX-P02-M230102 adapter, enabling MPC5X series cloning without opening the ECU cover.

Supports BOSCH MPC5xx platform mode ECUs: MED9.1, MED9.5, MED9.5.10, ME9.0, EDC16CP31, EDC16CP35, EDC16C2, EDC16C8.

2. Protect Original Car Parts

Over 98% of supported ECUs operate in BENCH mode and OBD mode—no need to open the ECU cover or drill holes, preserving the vehicle’s original components.

3. Intelligent Recognition

The “identification” function helps diagnose ECU communication status and wiring correctness. If the ECU is undamaged and properly connected, the system successfully reads chip, hardware, and firmware information.

4. Module Clone

Enables ECU data reading, writing, and module cloning without synchronization matching or online programming. Features data sub-regional burning and automatic verification to maximize chip and module protection.

5. ISN Read and Write

Supports ISN code acquisition for all BMW series (including Mini), facilitating key matching and anti-theft system maintenance.

6. VIN Modification

Resolves double VIN or VIN mismatch issues, simplifying vehicle maintenance tasks.

7. Data Processing

Supports engine computer data analysis and modification for Audi, Seat, Skoda, and Volkswagen models.
Supports disabling the anti-theft system on Bosch MED/EDC17 series engine computers.
Supports TPROT off function for:

• Bosch VAG MEDC17 series
• BMW/Mini MEVD17/EDC17 series
• Hyundai/Kia EDC17/MED(G)17 series

8. Broad ECU Compatibility

FC200 supports not only BMW ECUs but also over 3,000 additional ECU types, comparable to KTAG, Kess, and Dimsport.

9. Three Operating Modes

CAN-BUS, Bench Mode, and Boot Mode.

10. Multi-Language Support

Available languages: English, French, Simplified Chinese.
Traditional Chinese, Spanish, Polish, and Turkish require an additional fee.

11. Full Version with All Licenses Activated

Includes Denso and China Delphi licenses. Free online updates for one year. Annual renewal fee is $200/year after the first year.

12. MPC5XX Adapter for Non-Invasive Cloning

The CG FC200-MPC5XX-P02-M230102 adapter enables MPC5X series cloning without opening the ECU cover.

Supported ECU Models: ME9.0, MED9.1, MED9.5.10, EDC16C2, EDC16CB, EDC16CP31, EDC16CP35. Additional models are continuously being added.

CG FC200 Latest Update Information

CG FC200 V1.2.9.3 Registered Version (2025.07.16)

New Features:

1. DTC-OFF Function – Fourth Batch:
   VAG: MED17.1, MED17.1.1, MED17.1.6, MED17.1.21, MED17.1.27,
   MED17.5, MED17.5.2, MED17.5.5, MED17.5.21, MED17.5.25,
   MED9.1, ME7.5.10, ME7.5.20, ME7.5.30
   MG1CS008, MG1CS001, MG1CS111, MG1CS002
   Mercedes: SIM271DE, SIM271KE
   PSA: MED17.4, MED17.4.2, MED17.4.4, MD1CS003
   Land Rover: EDC17CP42, EDC17CP55, MEDC17.9
   Porsche: SDI4, SDI6, SDI7, SDI8, SDI9, SDI21.x
   Volvo: EDC17CP22, EDC17CP48
   Honda: EDC17CP16
   BMW: EDC17CP45
   Iveco: EDC17CP52
   Jeep: EDC17CP27
   Fiat: EDC17CP52, ME17.3.0
   Renault: MD1CS006
   CNH: EDC17CV41
   MAN: EDC17CV42
   Alfa Romeo: MED17.3.3
2. Idle Speed Modification:
   Honda:
   37820-Rxx-Hxx SH7058
   37820-5xx-Bxx SH72543
   
   Hyundai-Kia:
   ME17.9.11, ME17.9.1, ME17.9.11.1,
   MEG17.9.12, MEG17.9.13, MED17.9.8, MEG17.9.8, MEG17.9.21,
   SIM2K_140, SIM2K_141, SIM2K_341
3. New ECU Models Added:
   JBC/JAC: LINCONTROL LEC4AF, LEC4AP
   BAIC/Dongfeng/Geely/Changan/Proton: BOSCH MG1UA008, UP8
   DFM-Future: AECS FC-34
   VAG: CONTINENTAL Simos8.6
   Dongfeng: MD1CC878
   Fukuda: MD1CS089
   Buick: ME17.U.6
   FAW/Jiangling Motors: MD1CE108
   BYD/Haima: M7.9.7, M7.9.7.1, ME7.9.71

Bug Fixes:

1. Optimized PFlash writing failure in Wuling Easy-U3.6.
2. Optimized read/write failures in parts of Wuling Easy-U2.5 and U2W.

CG FC200 Update V1.2.9.2 (June 18th, 2025)

1. Added BMW Coolant Temperature Setting feature.
2. Expanded DTC Off support to more vehicle models.
3. Added support for new ECU models.
4. Extended "Three readiness monitors not ready" support to more ECU types.
5. Added Checksum toggle in Settings.
6. Added more ECU types supporting VIN Modification.

CG FC200 V1.2.9.1 Update (June 9th, 2025)

1. New ECU Models with DTC OFF Functions:
   BMW Bosch:
   (B48): MD1CP002, MD1CS001, MG1CS003, MG1CS201
   (N13/N20/N55/B38): MEVD17.2, MEVD17.2.3, MEVD17.2.4, MEVD17.2.5, MEVD17.2.6, MEVD17.2.8, MEVD17.2.9, MEVD17.2.G, MEVD17.2.H, MEVD17.2.K, MEVD17.2.P
   BMW Continental: MSD81, MSV90
   Ford-Bosch: MD1CS005
   Jaguar/Land Rover-Bosch: MED17.8.31, MED17.9.7, MED17.9.9
   Mercedes Benz Bosch: EDC17CP57, MD1CP001, MG1CP002
   Volkswagen Bosch: EDC17CP54, EDC17CP74, EDC17C74, MD1CP004, MD1CP014, MD1CS004
2. New ECU Models Added:
   Wuling:
   CONTINENTAL Easy_U2.5 SPC564xx
   CONTINENTAL Easy_U2W SPC564xx (1.2.9.2 upgrade)
   CONTINENTAL Easy_U3.6 SPC564xx (1.2.9.2 upgrade)
   CONTINENTAL Easy_U3D/U3E SPC564xx (1.2.9.2 upgrade)
   Geely: CONTINENTAL Easy_U2 SPC564xx

CG FC200 V1.2.9.0 Registered Version (2025.05.24)

New Functions:

1. DTC OFF Function – First Batch:
   BMW BOSCH: EDC16C31, EDC16C35, EDC16CP35, EDC17C06, EDC17C41, EDC17C50, EDC17C56, EDC17CP02, EDC17CP09
   Mercedes DELPHI: CRD2.x, CRD3.x
   Mercedes BOSCH: EDC16C32, EDC16CP31, DCU17PC42, EDC17C66, EDC17CP01, EDC17CP10
   Volkswagen DELPHI: DCM6.2
   Volkswagen BOSCH: EDC16U1, EDC16U31, EDC16U34, EDC16CP34, EDC17C46, EDC17C54, EDC17C64, EDC17C74, EDC17CP04, EDC17CP14, EDC17U01, EDC17U05
   Volkswagen CONTINENTAL: PCR2.1, SIMOS8.1, SIMOS8.2, SIMOS8.3, SIMOS8.4, SIMOS8.5
   Hyundai/Kia Bosch: EDC16C39, EDC17C08, EDC17C53, EDC17C57, EDC17CP14
   Opel GM: E78, E80, E83, E98
   Opel BOSCH: EDC16C39, EDC17C11, EDC17C18, EDC17C19, EDC17C42, EDC17C59, EDC17C60, EDC17C84
   Mazda DENSO: R2xx, RFxx, SH1x
   PSA DELPHI: DCM 3.5, DCM 6.2A, DCM 7.1A
   PSA BOSCH: EDC16C34, EDC17C10, EDC17C60
   Renault BOSCH: EDC16C36, EDC17C11, DC17C42, EDC17C84
   Subaru DENSO: KS/DT
   Toyota BOSCH: EDC17C73, EDC17CP07
   Toyota DENSO: Diesel Gen3
   Land Rover BOSCH: EDC17CP11
   Fiat BOSCH: EDC16C39, EDC17C49, EDC17C69
   Ford DELPHI: DCM6.1
   Ford BOSCH: EDC17C70, EDC17CP05
   Honda BOSCH: EDC17_CP06
   Iveco BOSCH: EDC16C39, EDC17C49, EDC17C69
   Jeep BOSCH: EDC17C79
   CNH BOSCH: EDC17C49
2. Newly Added ECU Models:
   Buick: MT60.1 MC9S12XEP768
   Wuling: MT60.1 MC9S12XEP768
   Shacman: EDC17CV44
   Great Wall: M7.9.7, M7.9.7.1, ME7.9.71, MT20U2 MC9S12XET256
   ChangHe: MT20U2 MC9S12XET256
   HAWTAI MOTOR: ME7.8.8, M7
   HAFEI: ME7.8.8, M7, TR40
   DongFeng: EDC17C81
   FOTON: TR40

Bug Fixes:

1. Fixed VIN modification failure on some Volkswagen ME17.5.22/24/26.
2. Resolved partial SID209 password read failure.

CG FC200 V1.2.8.0 Update Information (2025.05.20)

New Functions

1. Newly added models with "three items not ready" function:
   • BMW: MSV90, MEVD17.2.2, MEVD17.2.8, MEVD17.2.H
   • Hyundai/Kia: SIM2K-240, SIM2K_341
2. Volkswagen DQ380/DQ381 TCU adds "mileage repair" function
3. New Hyundai/Kia ECU/TCU:
   SIM2K-250_ECU, SIM2K-250_TCU, SIM2K-260, SIM2K-140_ECU, SIM2K-140_TCU, SIM2K-141_ECU, SIM2K-141_TCU
4. Add read-write function, "modify VIN" and "three items not ready" function to Xiali DFO JH30 module
5. Added read-write function, "VIN modification" and "three items not ready" function for SAIC Maxus DFO TR20 module
6. ECU with added verification function: MD1CC878, DCM3.7AP

Bug Fixes

1. Optimize the "three items not ready" function of DCM7.1AP
2. Fix the issue where some BOSCH TC17xx ECU prompts that the version is not supported
3. Fix the issue of failed verification of PFlash in CPEGP2.10.1
4. Optimize the verification function of DCM7.1AP
5. Optimize the verification function of GM E37/E78/E83
6. Optimize the verification function of PCR2.1
7. Optimize the verification function of 9HP
8. Optimize the verification function of MT80

CG FC200 V1.2.7.0 Update Information (2025.04.30)

New Functions

1. ECU with added "modify VIN" function:
   • BOSCH TC2xx:
     MD1CP001, MG1CS003, MD1CP002, MD1CS006, MG1CP002, MG1CS080, MD1CP004 SPC5777, MD1CP004_ TC298TP,
     MD1CS004, MG1CS001, MG1CS002 SPC5777, MG1CS002_ TC298TP, MG1CS111, MD1CP014, MG1CS008_ TC298TP, MG1CS016,
     MG1CS017, MG1CS018, MG1CS019, MG1CS032, MG1CS026, MG1CS024, MG1CS201, MD1CS001, MG1CA007
   • BOSCH TC17xx:
     EDC17U01, EDC17U05, ME17.5.20, MED17.1.61, EDC17CP74, ME17.7.8, EDC17CP06, EDC17CP16, DCU17PC42, EDC17CP58, MED17.6.9,
     EDC17CP68, EDC17C61, EDC17C47, ME17.8.31, ME17.8.32, EDC17CP05_ TC1797, EDC17CP05 TC1796, ME17.8.3.3, ME17.8.33, ME17.8.5, M17.8.7
   • BOSCH MPC 5xx:
     MED9.1, ME9.0, EDC16CP31, EDC16CP35, EDC16U31, EDC16C2, EDC16C1, EDC16U31, ME9.1.1, MED9.1.1, MED9.1.2
   • BOSCH ST10xx: ME7.7.0、ME7.9.9、ME7.1.1、ME7.8.2、ME7.6.4
   • CONTINENTAL/Siemens:
     SIM271KE, SIM271DE, SDI7, SDI6.1, SIMOS8.4x, SID208, SID310, EMS3110, EMS2511, EMS24xx, GPEC3, GPEC2A, GPEC4, GPEC4LM, GPEC2
   • DENSO:
     MB279700-9500, MB279700-9811, MB279700-9801, MB279700-96xx, RF7x, RF8x, 33920-67P0, R2xx, Pxxx, S5xx, SHxx, 275700_7082, RA6, 4N14,
     23740_5Sxxx_Gen2, 23740-5Sxxx_Gen2, 23740-3Nxxx_Gen1, Subaru SH72531, 112800 SH72531
   • GM: E38, E39, E39A, E78, E80, E83, E98, E84
   • Hyundai/Kia: SIM2K_240_ECU, SIM2K_241_ECU, SIM2K_240R_ECU
   • Mitsubishi: E6T6xxxx、E6TAxxxx
   • DELPHI: DCM3.7AP、DCM3.5
   • Marelli: 8TDW
2. Add the "Three Not Ready" function:
   • Peugeot/Citroen：MED17.4.2 TC1767, MED17.4.2_ TC1797, MED17.4.4, MEV17.4, MEVD17.4.4, MEV17.4.2 TC1766, MEV17.4.2_ TC1767
   • Maserati：MED17.3.4, MED17.3.5
   • Benz/Smart：ME7.7.0
   • BMW：ME17.2.1
3. ME17.8.8 adds CALID modification function
4. Dongfanghong tractor EDC17CV54 time repair
5. JMC EDC17C55 mileage repair
6. Added Volkswagen MG1CA811

CG FC200 V1.2.6.0 Registered Version New (2025.02.27)

New Functions

1. "Three readiness monitors not ready" function:
   • DELPHI: MT22.1, ME22.1.1, MT22U
   • Jiangling/Foton/Great Wall: EDC17C81/EDC17C63/EDC17C53
   • Jaguar Land Rover: MED17.0.1, MED17.0, MED17.9.7, MED17.9.8, MED17.9.9, MED17.8.31, MED17.8.32
   • Fiat: ME17.3.0
2. ECUs with newly added checksum: MT20U, MT22U, MT20U2, MT22.1, MT22.1.1
3. M7, ME7.8.8 added the function of modifying CALID code
4. Added Wuling SIM2K-D51 module, and supports verification function, VIN modification and three readiness monitors not ready functions
5. Added Wuling SCE60 module
6. Added Hyundai SIM2K-47 module
7. Added ECUs with VIN modification function:
   • Marelli ECU: 8GMK, 8GML, 9GC
   • Bosch ECU: ME7.4.5, M7.9.8
8. Added ECUs:
   • Volkswagen: simos12.1
   • Hyundai Kia: MEDG17.9.8

Bug Fixes

1. Optimized the read and write functions of ME17.9.23 and ME17.9.21.1, EDC17C69
2. Fixed the problem of some DCM7.1APs failing to read and write PFlash
3. Optimized three readiness monitors not ready of Wuling SIM2K-51.4

FC200 V1.2.5.2 Registered Version (2025.01.18)

New Functions

1. Added three ECUs with unready functions for domestic models:
   • Silver housing: ME17, ME17.8.8, MED17, MED17.8.10, MED17.8.2, MED17.8.21
   • Black housing (Black): ECU6.1, ME17, ME17.U.6, UP6
2. Added three ECUs with unready functions for Hyundai Kia: MEG17.9.12, MEG17.9.13, MEG17.9.2, MEG17.9.21, MEG17.9.8, ME17.9.1, ME17.9.11, ME17.9.11.1, ME17.9.21, ME17.9.21.1, MED17.9.30, MED17.9.8, EDC17CP14, ME17.9.8
3. Added Jinbei Lingdian ECU and supports VIN change and three unready functions: LINCONTROL LEC4A, LINCONTROL STC-213
4. Added Volkswagen Skoda ME7.5.20 three unready and VIN change functions
5. Chery ME7.9.7 added ExtFlash verification algorithm
6. Added Bosch ECU: UP6 TC1728, MED17.8.21, ME17.9.8
7. Added Huasong N20 model and supports VIN code change
8. Added BOSCH VIN change ECU: MEG17.9.13, ME17.9.1, EDC17CP48, EDC17C69, EDC17C83, ME17.3.0, EDC17C10, EDC17C58, ME17.0.3, EDC17C70

Bug Fixes

1. Fixed the issue of ME17/ME17.U.6/ECU6.1 failing to modify VIN
2. Optimized the verification algorithm of M7/ME7.8.8/M7.9.7/SIM2K-51.4
3. Fixed some bugs and optimized software performance

FC200 V1.2.5.1 Registered Version (2025.01.15)

New Functions

1. Added Wuling SIM2K-51.4 read/write, VIN modification, and three unready functions
2. Added Jinbei Lingdian TR40 read/write, VIN modification, and three unready functions
3. Added three unready functions of Volkswagen ECUs: MED17.1.6, MED17.1, MED17.5, MED17.5.1, MED17.5.2, ME17.5.22, MED17.1.10, MED17.5.20, MED17.5.25, MED17.5.5, EDC17CP14
4. Added three unready functions of BMW N20/N55/B38/N13 ECUs: MEVD17.2.5, MEVD17.2.4, MEVD17.2.9, MEVD17.2.P, MEVD17.2, MEVD17.2.6, MEVD17.2.G, MEVD17.2.K, MEVD17.2.3
5. Added verification function ECUs: ME7, ME7.8.8, ME7.9.7, ME7.9.71, M7.9.7, M7.9.7.1, ME7.5.20

Bug Fixes

1. Fixed the problem of failure to write PFlash data in some ME17.9.64
2. Fixed the problem of failure to backup data of Honda Keihin KEIHIN series ECU
3. Fixed the problem of PFlash verification failure of Hyundai Kia CPGDSH2.26.1
4. Fixed the VIN code change function for ME17.9.1, ME17.9.11, ME17.3.0, and EDC17C81
5. Fixed some bugs and optimized software performance

FC200 V1.2.5.0 Registered Version New (2025.01.06)

New Functions

1. Added the "Three readiness monitors not ready" function of GM E37\E38\E39\E39A\E78\E80\E83\E84 ECU
2. Added MELCO (Mitsubishi) series BENCH mode ECU:
   • MELCO E6T6xxxx MH8501F
   • MELCO E6TAxxxx MPC5746R
   • MELCO E6T85xxx MH8601 test
   • MELCO E6T8xxxx MH8115 test
   • MELCO E6T7xxxx MH8611 test
   • MELCO E6T86xxx MH8115 test
3. Added BOSCH (Bosch) BENCH mode ECU\TCU:
   • MG1CS080 TC275TP test
   • INVCON2.3 TC1797
   • HV17.4.1 TC1797
4. Added the "Repair of Lovol engine duration" of data processing to Lovol ECU: EDC17C63, EDC17CV54
5. Added the BOOT mode read and write function for GM E83
6. Added the function of reading and writing DFlash, PFlash, Maps, and ExtEEPROM separately for Mercedes-Benz SIM271DE
7. Added the "Unlock" function of VOLVO MB279700-96xx
8. Added "Read Password" function in Hyundai Kia CPEGP2.10.1 boot mode

Bug Fixes

• Optimized the "Turn off anti-theft" function of EDC17C53, EDC17C63, and EDC17C81
• Optimized Porsche SDI10.x ECU wiring diagram
• Fixed the problem that Mercedes-Benz CRD3P.C0 and CRD3P.D1 can not be read and written
• Fixed the problem that DCM2.5 failed to write PFlash
• Fixed the problem that M7 failed to recognize but can read and write
• Fixed the problem that VGS2-FDTC failed to recognize after the updated version
• Optimized the process of M7.9.7, M7.9.7.1, ME7.9.7, ME7.9.7.1 to handle the "Three readiness monitors not ready" function
• Fixed the problem that Honda 37820 SH7058 does not communicate with ECU after writing data

FC200 ECU Programmer Powerful Functions

1. Original Parts Protection

FC200 supports OBD and platform mode for more than 98% ECU and EGS, no need to open shell, no punch, protect original parts of the vehicle.

2. Smart Identification

The "identification" function can help users diagnose whether the ECU module is communicating and check whether the wiring is wrong.
If ECU module is not damaged and can be communicated, wiring is correct and identification is successful, can read chip and firmware information.

3. Module Clone

Supports ECU/EGS reading & writing and modules clone, synchronization matching free, no need online programming.
Flash data by area, automatically check, protect chips and modules furthest.

4. ISN Reading and Writing

Supports all BMW series (including Mini) ECU ISN code acquisition, convenient for all keys lost matching and anti-theft fault maintenance.

5. VIN Writing

Solve the problem of double VIN or VIN mismatch of vehicles, convenient for vehicle maintenance.

6. Data Processing

Support data analysis and modification for the 4th and 5th generations of Audi/Seat/Skoda/Volkswagen ECUs.
Turn off anti-theft system for Bosch MED/EDC17 series ECU.
TPROT off function of Bosch VAG MEDC17 series, BMW/Mini MEVD17/EDC17 series, Hyundai/Kia EDC17/MED(G)17 series.

FC200 ECU Programmer Software Display

1. Interactive Software Interface

Brand-model-engine/gearbox-ECU interface structure to help users save time and find the operating directory accurately.

2. Built-in Model Search Function

Support ECU model and Bosch search by number, avoid the trouble of level selection, and enter the function interface as quickly as possible.

3. ECU Search

Take the BMW MSV90 ECU as an example: First select "BMW", select "ECU" as the search condition, enter "MSV90", click the search button, and the ECU type will show up.
Same search procedure for Bosch ECUs.

4. Visualized Wiring Diagram

1:1 simulation, bright colors, to avoid wiring errors.

FC200 ECU Programmer Hardware

FC200 Main Unit

1. Integrated injection of polymer materials, professional customized internal circuit boards, national patent certification

2. Exquisite design, easy to carry, can shield surrounding interference signals, adapt to various operating environments

3. There are 3 expansion ports for peripherals, which are automatically diagnosed and identified. They are 12V power port, USB port and DB15 port. The DB15 port can be connected to a free-dismantling adapter and OBD cable.

FC200 Adapters

1. Vehicle-grade wiring harness, made of synthetic metal, has excellent internal conductivity, and can be used continuously for 10,000 times.

2. Tight design, seamless connection between ECU and host to ensure continuous communication and escort your operation

3. Equipped with B-type, C-type, D-type, F-type and G-Type pin interfaces, suitable for many types of ECU and EGS

OBD2 Cable

FC200 OBD2 cable mainly suitable for BMW B48/B58 ECU at present, read ISN via OBD without disassembly.
110cm, made of synthetic material, resistant to high temperature, waterproof, anti-corrosion is designed according to OBD port of the vehicles, built-in anti-falling buckle make connection stable.

CG FC-200 Package

• 1pc x CGDI FC200 Host
• 1pc x OBD Cable
• 1pc x Jumper
• 1pc x USB Cable
• 6pcs x G-type Adapter Cable
• 3pcs x F-type Adapter Cable
• 6pcs x E-type Adapter Cable
• 6pcs x D-type Adapter Cable
• 6pcs x C-type Adapter Cable
• 6pcs x B-type Adapter Cable
• 1pc x MPC5XX Adapter